Load Balancer as a Service (LBaaS)

Load Balancer as a Service (LBaaS)

The Networking service offers two load balancer implementations through the neutron-lbaas service plug-in:

  • LBaaS v1: introduced in Juno (deprecated in Liberty)
  • LBaaS v2: introduced in Kilo

Both implementations use agents. The agents handle the HAProxy configuration and manage the HAProxy daemon. LBaaS v2 adds the concept of listeners to the LBaaS v1 load balancers. LBaaS v2 allows you to configure multiple listener ports on a single load balancer IP address.

Another LBaaS v2 implementation, Octavia, has a separate API and separate worker processes that build load balancers within virtual machines on hypervisors that are managed by the Compute service. You do not need an agent for Octavia.

Currently, no migration path exists between v1 and v2 load balancers. If you choose to switch from v1 to v2, you must recreate all load balancers, pools, and health monitors.

LBaaS v1

LBaaS v1 is deprecated in the Liberty release. These links provide more details about how LBaaS v1 works and how to configure it:

LBaaS v2

LBaaS v2 has several new concepts to understand:

LBaaS v2 layout
Load balancer
The load balancer occupies a neutron network port and has an IP address assigned from a subnet.
Listener
Load balancers can listen for requests on multiple ports. Each one of those ports is specified by a listener.
Pool
A pool holds a list of members that serve content through the load balancer.
Member
Members are servers that serve traffic behind a load balancer. Each member is specified by the IP address and port that it uses to serve traffic.
Health monitor
Members may go offline from time to time and health monitors divert traffic away from members that are not responding properly. Health monitors are associated with pools.

LBaaS v2 has multiple implementations via different service plug-ins. The two most common implementations use either an agent or the Octavia services. Both implementations use the LBaaS v2 API.

Configuring LBaaS v2 with an agent

  1. Add the LBaaS v2 service plug-in to the service_plugins configuration directive in /etc/neutron/neutron.conf. The plug-in list is comma-separated:

    service_plugins = [existing service plugins],neutron_lbaas.services.loadbalancer.plugin.LoadBalancerPluginv2
    
  2. Add the LBaaS v2 service provider to the service_provider configuration directive within the [service_providers] section in /etc/neutron/neutron.conf:

    service_provider = LOADBALANCERV2:Haproxy:neutron_lbaas.drivers.haproxy.plugin_driver.HaproxyOnHostPluginDriver:default
    

    If you have existing service providers for other networking service plug-ins, such as VPNaaS or FWaaS, add the service_provider line shown above in the [service_providers] section as a separate line. These configuration directives are repeatable and are not comma-separated.

  3. Run the neutron-lbaas database migration:

    neutron-db-manage --service lbaas upgrade head
    
  4. If you have deployed LBaaS v1, stop the LBaaS v1 agent now. The v1 and v2 agents cannot run simultaneously.

  5. Start the LBaaS v2 agent:

    neutron-lbaasv2-agent \
    --config-file /etc/neutron/neutron.conf \
    --config-file /etc/neutron/lbaas_agent.ini
    
  6. Restart the Network service to activate the new configuration. You are now ready to create load balancers with the LBaaS v2 agent.

Configuring LBaaS v2 with Octavia

Octavia provides additional capabilities for load balancers, including using a compute driver to build instances that operate as load balancers. The Hands on Lab - Install and Configure OpenStack Octavia session at the OpenStack Summit in Tokyo provides an overview of Octavia.

The DevStack documentation offers a simple method to deploy Octavia and test the service with redundant load balancer instances. If you already have Octavia installed and configured within your environment, you can configure the Network service to use Octavia:

  1. Add the LBaaS v2 service plug-in to the service_plugins configuration directive in /etc/neutron/neutron.conf. The plug-in list is comma-separated:

    service_plugins = [existing service plugins],neutron_lbaas.services.loadbalancer.plugin.LoadBalancerPluginv2
    
  2. Add the Octavia service provider to the service_provider configuration directive within the [service_providers] section in /etc/neutron/neutron.conf:

    service_provider = LOADBALANCERV2:Octavia:neutron_lbaas.drivers.octavia.driver.OctaviaDriver:default
    

    Ensure that the LBaaS v1 and v2 service providers are removed from the [service_providers] section. They are not used with Octavia. Verify that all LBaaS agents are stopped.

  3. Restart the Network service to activate the new configuration. You are now ready to create and manage load balancers with Octavia.

LBaaS v2 operations

The same neutron commands are used for LBaaS v2 with an agent or with Octavia.

Building an LBaaS v2 load balancer

  1. Start by creating a load balancer on a network. In this example, the private network is an isolated network with two web server instances:

    $ neutron lbaas-loadbalancer-create --name test-lb private-subnet
    
  2. You can view the load balancer status and IP address with the lbaas-loadbalancer-show command:

    $ neutron lbaas-loadbalancer-show test-lb
    +---------------------+------------------------------------------------+
    | Field               | Value                                          |
    +---------------------+------------------------------------------------+
    | admin_state_up      | True                                           |
    | description         |                                                |
    | id                  | 7780f9dd-e5dd-43a9-af81-0d2d1bd9c386           |
    | listeners           | {"id": "23442d6a-4d82-40ee-8d08-243750dbc191"} |
    |                     | {"id": "7e0d084d-6d67-47e6-9f77-0115e6cf9ba8"} |
    | name                | test-lb                                        |
    | operating_status    | ONLINE                                         |
    | provider            | haproxy                                        |
    | provisioning_status | ACTIVE                                         |
    | tenant_id           | fbfce4cb346c4f9097a977c54904cafd               |
    | vip_address         | 192.168.1.22                                   |
    | vip_port_id         | 9f8f8a75-a731-4a34-b622-864907e1d556           |
    | vip_subnet_id       | f1e7827d-1bfe-40b6-b8f0-2d9fd946f59b           |
     +---------------------+------------------------------------------------+
    
  3. Update the security group to allow traffic to reach the new load balancer. Create a new security group along with ingress rules to allow traffic into the new load balancer. The neutron port for the load balancer is shown as vip_port_id above.

    Create a security group and rules to allow TCP port 80, TCP port 443, and all ICMP traffic:

    $ neutron security-group-create lbaas
    $ neutron security-group-rule-create \
      --direction ingress \
      --protocol tcp \
      --port-range-min 80 \
      --port-range-max 80 \
      --remote-ip-prefix 0.0.0.0/0 \
      lbaas
    $ neutron security-group-rule-create \
      --direction ingress \
      --protocol tcp \
      --port-range-min 443 \
      --port-range-max 443 \
      --remote-ip-prefix 0.0.0.0/0 \
      lbaas
    $ security-group-rule-create \
      --direction ingress \
      --protocol icmp \
      lbaas
    

    Apply the security group to the load balancer’s network port using vip_port_id from the lbaas-loadbalancer-show command:

    $ neutron port-update \
      --security-group lbaas \
      9f8f8a75-a731-4a34-b622-864907e1d556
    

    This load balancer is active and ready to serve traffic on 192.168.1.22.

  4. Verify that the load balancer is responding to pings before moving further:

    $ ping -c 4 192.168.1.22
    PING 192.168.1.22 (192.168.1.22) 56(84) bytes of data.
    64 bytes from 192.168.1.22: icmp_seq=1 ttl=62 time=0.410 ms
    64 bytes from 192.168.1.22: icmp_seq=2 ttl=62 time=0.407 ms
    64 bytes from 192.168.1.22: icmp_seq=3 ttl=62 time=0.396 ms
    64 bytes from 192.168.1.22: icmp_seq=4 ttl=62 time=0.397 ms
    
    --- 192.168.1.22 ping statistics ---
    4 packets transmitted, 4 received, 0% packet loss, time 2997ms
    rtt min/avg/max/mdev = 0.396/0.402/0.410/0.020 ms
    

Adding an HTTP listener

  1. With the load balancer online, you can add a listener for plaintext HTTP traffic on port 80:

    $ neutron lbaas-listener-create \
      --name test-lb-http \
      --loadbalancer test-lb \
      --protocol HTTP \
      --protocol-port 80
    
  2. You can begin building a pool and adding members to the pool to serve HTTP content on port 80. For this example, the web servers are 192.168.1.16 and 192.168.1.17:

    $ neutron lbaas-pool-create \
      --name test-lb-pool-http \
      --lb-algorithm ROUND_ROBIN \
      --listener test-lb-http \
      --protocol HTTP
    $ neutron lbaas-member-create \
      --subnet private-subnet \
      --address 192.168.1.16 \
      --protocol-port 80 \
      test-lb-pool-http
    $ neutron lbaas-member-create \
      --subnet private-subnet \
      --address 192.168.1.17 \
      --protocol-port 80 \
      test-lb-pool-http
    
  3. You can use curl to verify connectivity through the load balancers to your web servers:

    $ curl 192.168.1.22
    web2
    $ curl 192.168.1.22
    web1
    $ curl 192.168.1.22
    web2
    $ curl 192.168.1.22
    web1
    

    In this example, the load balancer uses the round robin algorithm and the traffic alternates between the web servers on the backend.

  4. You can add a health monitor so that unresponsive servers are removed from the pool:

    $ neutron lbaas-healthmonitor-create \
      --delay 5 \
      --max-retries 2 \
      --timeout 10 \
      --type HTTP \
      --pool test-lb-pool-http
    

    In this example, the health monitor removes the server from the pool if it fails a health check at two five-second intervals. When the server recovers and begins responding to health checks again, it is added to the pool once again.

Adding an HTTPS listener

You can add another listener on port 443 for HTTPS traffic. LBaaS v2 offers SSL/TLS termination at the load balancer, but this example takes a simpler approach and allows encrypted connections to terminate at each member server.

  1. Start by creating a listener, attaching a pool, and then adding members:

    $ neutron lbaas-listener-create \
      --name test-lb-https \
      --loadbalancer test-lb \
      --protocol HTTPS \
      --protocol-port 443
    $ neutron lbaas-pool-create \
      --name test-lb-pool-https \
      --lb-algorithm LEAST_CONNECTIONS \
      --listener test-lb-https \
      --protocol HTTPS
    $ neutron lbaas-member-create \
      --subnet private-subnet \
      --address 192.168.1.16 \
      --protocol-port 443 \
      test-lb-pool-https
    $ neutron lbaas-member-create \
      --subnet private-subnet \
      --address 192.168.1.17 \
      --protocol-port 443 \
      test-lb-pool-https
    
  2. You can also add a health monitor for the HTTPS pool:

    $ neutron lbaas-healthmonitor-create \
      --delay 5 \
      --max-retries 2 \
      --timeout 10 \
      --type HTTPS \
      --pool test-lb-pool-https
    

    The load balancer now handles traffic on ports 80 and 443.

Associating a floating IP address

Load balancers that are deployed on a public or provider network that are accessible to external clients do not need a floating IP address assigned. External clients can directly access the virtual IP address (VIP) of those load balancers.

However, load balancers deployed onto private or isolated networks need a floating IP address assigned if they must be accessible to external clients. To complete this step, you must have a router between the private and public networks and an available floating IP address.

You can use the lbaas-loadbalancer-show command from the beginning of this section to locate the vip_port_id. The vip_port_id is the ID of the network port that is assigned to the load balancer. You can associate a free floating IP address to the load balancer using floatingip-associate:

$ neutron floatingip-associate FLOATINGIP_ID LOAD_BALANCER_PORT_ID

Setting quotas for LBaaS v2

Quotas are available for limiting the number of load balancers and load balancer pools. By default, both quotas are set to 10.

You can adjust quotas using the quota-update command:

$ neutron quota-update --tenant-id TENANT_UUID --loadbalancer 25
$ neutron quota-update --tenant-id TENANT_UUID --pool 50

A setting of -1 disables the quota for a tenant.

Retrieving load balancer statistics

The LBaaS v2 agent collects four types of statistics for each load balancer every six seconds. Users can query these statistics with the lbaas-loadbalancer-stats command:

$ neutron lbaas-loadbalancer-stats test-lb
+--------------------+----------+
| Field              | Value    |
+--------------------+----------+
| active_connections | 0        |
| bytes_in           | 40264557 |
| bytes_out          | 71701666 |
| total_connections  | 384601   |
+--------------------+----------+

The active_connections count is the total number of connections that were active at the time the agent polled the load balancer. The other three statistics are cumulative since the load balancer was last started. For example, if the load balancer restarts due to a system error or a configuration change, these statistics will be reset.

Creative Commons Attribution 3.0 License

Except where otherwise noted, this document is licensed under Creative Commons Attribution 3.0 License. See all OpenStack Legal Documents.