L3 HA Scheduling of Gateway Chassis

Problem Description

Currently if a single network node is active in the system, gateway chassis for the routers would be scheduled on that node. However, when a new node is added to the system, neither rescheduling nor rebalancing occur automatically. This makes the router created on the first node to be not in HA mode.

Side-effects of this behavior include:

  • Skewed up load on different network nodes due to lack of router rescheduling.

  • If the active node, where the gateway chassis for a router is scheduled goes down, then because of lack of HA the North-South traffic from that router will be hampered.

Overview of Proposed Approach

Gateway scheduling has been proposed in [2]. However, rebalancing or rescheduling was not a part of that solution. This specification clarifies what is rescheduling and rebalancing. Rescheduling would automatically happen on every event triggered by addition or deletion of chassis. Rebalancing would be only triggered by manual operator action.

Rescheduling of Gateway Chassis

In order to provide proper rescheduling of the gateway ports during addition or deletion of the chassis, following approach can be considered:

  • Identify the number of chassis in which each router has been scheduled

    • Consider router for scheduling if no. of chassis < MAX_GW_CHASSIS

MAX_GW_CHASSIS is defined in [0]

  • Find a list of chassis where router is scheduled and reschedule it up to MAX_GW_CHASSIS gateways using list of available candidates. Do not modify the master chassis association to not interrupt network flows.

Rescheduling is an event triggered operation which will occur whenever a chassis is added or removed. When it happend, schedule_unhosted_gateways() [1] will be called to host the unhosted gateways. Routers without gateway ports are excluded in this operation because those are not connected to provider networks and haven’t the gateway ports. More information about it can be found in the gateway_chassis table definition in OVN NorthBound DB [5].

Chassis which has the flag enable-chassis-as-gw enabled in their OVN southbound database table, would be the ones eligible for hosting the routers. Rescheduling of router depends on current prorities set. Each chassis is given a specific priority for the router’s gateway and priority increases with increasing value ( i.e. 1 < 2 < 3 …). The highest prioritized chassis hosts gateway port. Other chassis are selected as slaves.

There are two approaches for rescheduling supported by networking-ovn right now: * Least loaded - select least-loaded chassis first, * Random - select chassis randomly.

Few points to consider for the design:

  • If there are 2 Chassis C1 and C2, where the routers are already balanced, and a new chassis C3 is added, then routers should be rescheduled only from C1 to C3 and C2 to C3. Rescheduling from C1 to C2 and vice-versa should not be allowed.

  • In order to reschedule the router’s chassis, the master chassis for a gateway router will be left untouched. However, for the scenario where all routers are scheduled in only one chassis which is available as gateway, the addition of the second gateway chassis would schedule the router gateway ports at a lower priority on the new chassis.

Following scenarios are possible which have been considered in the design:

  • Case #1:
    • System has only one chassis C1 and all router gateway ports are scheduled on it. We add a new chassis C2.

    • Behavior: All the routers scheduled on C1 will also be scheduled on C2 with priority 1.

  • Case #2:
    • System has 2 chassis C1 and C2 during installation. C1 goes down.

    • Behavior: In this case, all routers would be rescheduled to C2. Once C1 is back up, routers would be rescheduled on it. However, since C2 is now the new master, routers on C1 would have lower priority.

  • Case #3:
    • System has 2 chassis C1 and C2 during installation. C3 is added to it.

    • Behavior: In this case, routers would not move their master chassis associations. So routers which have their master on C1, would remain there, and same for routers on C2. However, lower proritized candidates of existing gateways would be scheduled on the chassis C3, depending on the type of used scheduler (Random or LeastLoaded).

Rebalancing of Gateway Chassis

Rebalancing is the second part of the design and it assigns a new master to already scheduled router gateway ports. Downtime is expected in this operation. Rebalancing of routers can be achieved using external cli script. Similar approach has been implemeneted for DHCP rescheduling [4]. The master chassis gateway could be moved only to other, previously scheduled gateway. Rebalancing of chassis occurs only if number of scheduled master chassis ports per each provider network hosted by given chassis is higher than average number of hosted master gateway ports per chassis per provider network.

This dependency is determined by formula:

avg_gw_per_chassis = num_gw_by_provider_net / num_chassis_with_provider_net

Where:
  • avg_gw_per_chassis - average number of scheduler master gateway chassis withing same provider network.

  • num_gw_by_provider_net - number of master chassis gateways scheduled in given provider networks.

  • num_chassis_with_provider_net - number of chassis that has connectivity to given provider network.

The rebalancing occurs only if:

num_gw_by_provider_net_by_chassis > avg_gw_per_chassis

Where:
  • num_gw_by_provider_net_by_chassis - number of hosted master gateways by given provider network by given chassis

  • avg_gw_per_chassis - average number of scheduler master gateway chassis withing same provider network.

Following scenarios are possible which have been considered in the design:

  • Case #1:
    • System has only two chassis C1 and C2. Chassis host the same number of gateways.

    • Behavior: Rebalancing doesn’t occur.

  • Case #2:
    • System has only two chassis C1 and C2. C1 hosts 3 gateways. C2 hosts 2 gateways.

    • Behavior: Rebalancing doesn’t occur to not continuously move gateways between chassis in loop.

  • Case #3:
    • System has two chassis C1 and C2. In meantime third chassis C3 has been added to the system.

    • Behavior: Rebalancing should occur. Gateways from C1 and C2 should be moved to C3 up to avg_gw_per_chassis.

  • Case #4:
    • System has two chassis C1 and C2. C1 is connected to provnet1, but C2 is connected to provnet2.

    • Behavior: Rebalancing shouldn’t occur because of lack of chassis within same provider network.

References