Configure live migrations¶
Migration enables an administrator to move a virtual machine instance from one compute host to another. A typical scenario is planned maintenance on the source host, but migration can also be useful to redistribute the load when many VM instances are running on a specific physical machine.
This document covers live migrations using the Libvirt and VMWare hypervisors
Not all Compute service hypervisor drivers support live-migration, or support all live-migration features. Similarly not all compute service features are supported.
Consult Feature Support Matrix to determine which hypervisors support live-migration.
See the Configuration Guide for details on hypervisor configuration settings.
The migration types are:
Non-live migration, also known as cold migration or simply migration.
The instance is shut down, then moved to another hypervisor and restarted. The instance recognizes that it was rebooted, and the application running on the instance is disrupted.
This section does not cover cold migration.
The instance keeps running throughout the migration. This is useful when it is not possible or desirable to stop the application running on the instance.
Live migrations can be classified further by the way they treat instance storage:
Shared storage-based live migration. The instance has ephemeral disks that are located on storage shared between the source and destination hosts.
Block live migration, or simply block migration. The instance has ephemeral disks that are not shared between the source and destination hosts. Block migration is incompatible with read-only devices such as CD-ROMs and Configuration Drive (config_drive).
Volume-backed live migration. Instances use volumes rather than ephemeral disks.
Block live migration requires copying disks from the source to the destination host. It takes more time and puts more load on the network. Shared-storage and volume-backed live migration does not copy disks.
In a multi-cell cloud, instances can be live migrated to a different host in the same cell, but not across cells. Refer to the cells v2 documentation. for more information.
The following sections describe how to configure your hosts for live migrations using the libvirt virt driver and KVM hypervisor.
To enable any type of live migration, configure the compute hosts according to the instructions below:
Set the following parameters in
nova.confon all compute hosts:
You must not make the VNC server listen to the IP address of its compute host, since that addresses changes when the instance is migrated.
Since this setting allows VNC clients from any IP address to connect to instance consoles, you must take additional measures like secure networks or firewalls to prevent potential attackers from gaining access to instances.
instances_pathmust have the same value for all compute hosts. In this guide, the value
Ensure that name resolution on all compute hosts is identical, so that they can connect each other through their hostnames.
If you use
/etc/hostsfor name resolution and enable SELinux, ensure that
/etc/hostshas the correct SELinux context:
# restorecon /etc/hosts
Enable password-less SSH so that root on one compute host can log on to any other compute host without providing a password. The
libvirtddaemon, which runs as root, uses the SSH protocol to copy the instance to the destination and can’t know the passwords of all compute hosts.
You may, for example, compile root’s public SSH keys on all compute hosts into an
authorized_keysfile and deploy that file to the compute hosts.
Configure the firewalls to allow libvirt to communicate between compute hosts.
By default, libvirt uses the TCP port range from 49152 to 49261 for copying memory and disk contents. Compute hosts must accept connections in this range.
For information about ports used by libvirt, see the libvirt documentation.
Be mindful of the security risks introduced by opening ports.
Securing live migration streams¶
If your compute nodes have at least libvirt 4.4.0 and QEMU 2.11.0, it is strongly recommended to secure all your live migration streams by taking advantage of the “QEMU-native TLS” feature. This requires a pre-existing PKI (Public Key Infrastructure) setup. For further details on how to set this all up, refer to the Secure live migration with QEMU-native TLS document.
Block migration, volume-based live migration¶
If your environment satisfies the requirements for “QEMU-native TLS”, then block migration requires some setup; refer to the above section, Securing live migration streams, for details. Otherwise, no additional configuration is required for block migration and volume-backed live migration.
Be aware that block migration adds load to the network and storage subsystems.
Advanced configuration for KVM and QEMU¶
Live migration copies the instance’s memory from the source to the destination compute host. After a memory page has been copied, the instance may write to it again, so that it has to be copied again. Instances that frequently write to different memory pages can overwhelm the memory copy process and prevent the live migration from completing.
This section covers configuration settings that can help live migration of memory-intensive instances succeed.
Live migration completion timeout
The Compute service will either abort or force complete a migration when it has been running too long. This behavior is configurable using the
libvirt.live_migration_timeout_actionconfig option. The timeout is calculated based on the instance size, which is the instance’s memory size in GiB. In the case of block migration, the size of ephemeral storage in GiB is added.
The timeout in seconds is the instance size multiplied by the configurable parameter
libvirt.live_migration_completion_timeout, whose default is 800. For example, shared-storage live migration of an instance with 8GiB memory will time out after 6400 seconds.
Near the end of the memory copy, the instance is paused for a short time so that the remaining few pages can be copied without interference from instance memory writes. The Compute service initializes this time to a small value that depends on the instance size, typically around 50 milliseconds. When it notices that the memory copy does not make sufficient progress, it increases the time gradually.
You can influence the instance downtime algorithm with the help of three configuration variables on the compute hosts:
live_migration_downtime = 500 live_migration_downtime_steps = 10 live_migration_downtime_delay = 75
live_migration_downtimesets the target maximum period of time Nova will try to keep the instance paused during the last part of the memory copy, in milliseconds. This value may be exceeded if there is any reduction on the transfer rate after the VM is paused. The default is 500.
live_migration_downtime_stepssets the total number of adjustment steps until
live_migration_downtimeis reached. The default is 10 steps.
live_migration_downtime_delaysets the time interval between two adjustment steps in seconds. The default is 75.
One strategy for a successful live migration of a memory-intensive instance is slowing the instance down. This is called auto-convergence. Both libvirt and QEMU implement this feature by automatically throttling the instance’s CPU when memory copy delays are detected.
Auto-convergence is disabled by default. You can enable it by setting
Before enabling auto-convergence, make sure that the instance’s application tolerates a slow-down.
Be aware that auto-convergence does not guarantee live migration success.
Live migration of a memory-intensive instance is certain to succeed when you enable post-copy. This feature, implemented by libvirt and QEMU, activates the virtual machine on the destination host before all of its memory has been copied. When the virtual machine accesses a page that is missing on the destination host, the resulting page fault is resolved by copying the page from the source host.
Post-copy is disabled by default. You can enable it by setting
When you enable both auto-convergence and post-copy, auto-convergence remains disabled.
The page faults introduced by post-copy can slow the instance down.
When the network connection between source and destination host is interrupted, page faults cannot be resolved anymore and the instance is rebooted.
The full list of live migration configuration parameters is documented in the Nova Configuration Options
Enable vMotion on all ESX hosts which are managed by Nova by following the instructions in this KB article.