Running benchmark

Running benchmark

Introduction

This document describes how to run benchmarking tool.

Zaqar Contributors can use this tool to test how the particular code change affects Zaqar’s performance.

Usage

  1. First install and run zaqar-server.

    For example, you can setup Zaqar in development environment.

    See Setting up a development environment.

  2. In your terminal cd into your local Zaqar repo and install additional requirements:

    $ pip install -r bench-requirements.txt
    
  3. Copy the configuration file to ~/.zaqar:

    $ cp etc/zaqar-benchmark.conf.sample ~/.zaqar/zaqar-benchmark.conf
    
  4. In this configuration file specify where zaqar-server can be found:

    server_url = http://localhost:8888
    
  5. The benchmarking tool needs a set of messages to work with. Specify the path to the file with messages in the configuration file. Alternatively, put it in the directory with the configuration file and name it zaqar-benchmark-messages.json. As a starting point, you can use the sample file from the etc directory:

    $ cp etc/zaqar-benchmark-messages.json ~/.zaqar/
    

    If the file is not found or no file is specified, a single hard-coded message is used for all requests.

  6. Run the benchmarking tool using the following command:

    $ zaqar-bench
    

    By default, the command will run a performance test for 5 seconds, using one producer process with 10 greenlet workers, and one observer process with 5 workers. The consumer role is disabled by default.

    You can override these defaults in the config file or on the command line using a variety of options. For example, the following command runs a performance test for 30 seconds using 4 producer processes with 20 workers each, plus 4 consumer processes with 20 workers each.

    Note that the observer role is also disabled in this example by setting its number of workers to zero:

    $ zaqar-bench -pp 4 -pw 10 -cp 4 -cw 20 -ow 0 -t 30
    

    By default, the results are in human-readable format. For JSON output add the --noverbose flag. The non-verbose output looks similar to the following:

    $ zaqar-bench --noverbose
    Using 'envvars' credentials
    Using 'keystone' authentication method
    Benchmarking Zaqar API v2...
    {"params": {"consumer": {"processes": 1, "workers": 0}, "observer": {"processes": 1, "workers": 5}, "producer": {"processes": 1, "workers": 10}}, "consumer": {"claim_total_requests": 0, "ms_per_claim": 0, "total_reqs": 0, "reqs_per_sec": 0, "successful_reqs": 0, "duration_sec": 0, "ms_per_delete": 0, "messages_processed": 0}, "producer": {"duration_sec": 8.569170951843262, "ms_per_req": 201.715140507139, "total_reqs": 29, "successful_reqs": 29, "reqs_per_sec": 3.384224700729303}, "observer": {"duration_sec": 8.481178045272827, "ms_per_req": 407.40778711107043, "total_reqs": 18, "successful_reqs": 18, "reqs_per_sec": 2.122346672115049}}
    

    By default, zaqar-bench is benchmarking Zaqar API version 2. To run benchmark against other API versions use -api parameter. For example:

    $ zaqar-bench -api 1.1
    

Configuring zaqar-bench to use Keystone authentication

It’s possible to use zaqar-bench with Keystone authentication, if your Zaqar is configured to use Keystone authentication method and the Keystone service is running. For example, this is always true when running DevStack with unmodified zaqar.conf.

Let’s configure zaqar-bench too to use Keystone:

  1. Set zaqar-bench’s authentication method to Keystone.

    By default zaqar-bench is using noauth method. This can be changed by setting the environment variable OS_AUTH_STRATEGY to keystone.

    To set this environment variable:

    • temporarily, run:

      $ export OS_AUTH_STRATEGY=keystone
      
    • permanently, add this line to your ~/bashrc file:

      export OS_AUTH_STRATEGY=keystone
      

      Reboot your computer or just run in the terminal where you will start zaqar-bench:

      $ source ~/.bashrc
      
  2. Set Keystone credentials for zaqar-bench.

    • If you’re running Zaqar under DevStack, you can omit this step, because zaqar-bench will automatically get administrator or user credentials from the one of the files created by DevStack: either from /etc/openstack/clouds.yaml file or from ~/.config/openstack/clouds.yaml file, if it exists.

    • If you’re running manually configured Zaqar with manually configured Keystone (not under DevStack):

      Add these lines to your ~/.bashrc file and specify the valid Keystone credentials:

      export OS_AUTH_URL="http://<your keystone endpoint>/v2.0"
      export OS_USERNAME="<keystone user name>"
      export OS_PASSWORD="<the user's password>"
      export OS_PROJECT_NAME="<keystone project name for the user>"
      

      Reboot your computer or just run in the terminal where you will start zaqar-bench:

      $ source ~/.bashrc
      
  3. Run zaqar-bench as usual, for example:

    $ zaqar-bench
    

    If everything is properly configured, zaqar-bench must show the line Using 'keystone' authentication method and execute without authentication errors.

Creative Commons Attribution 3.0 License

Except where otherwise noted, this document is licensed under Creative Commons Attribution 3.0 License. See all OpenStack Legal Documents.